Pre-Painted

Pre-Painted Hot Dipped Galvanized Steel Product
Hot Dipped Galvanizing

PPGI is prepainted galvanised steel, also known as precoated steel, coil coated steel, color coated steel etc.A galvanised steel sheet in coil form is cleaned, pretreated, applied with various layers of organic coatings which can be paints, vinyl dispersions, or laminates.These coatings are applied in a continuous process known as Coil Coating.The steel thus produced in this process is a prepainted, prefinished ready to use material. PPGI is the material which uses galvanised steel as the basic substrate metal. There could be other substrates such as aluminum, Galvalume, stainless steel, etc.

Characterisitcs:

Product Specification:
Basic Substrate: Cold rolled HDG / Galvalume
Quality: CQ  DQ
Color Standard: Acc to Ral Color Standard or customer's color sample

Item
Range
Item
Range
Thickness
0.23mm-1.2mm
Zinc spangle
Regular, Minimum
Width
700mm-1250mm
Surface Treatment
Bright/Matt Finishing
Zinc Weight
70g/m2-300g/m2
Coil Weight
3MT-10MT
I.D
508mm/610mm
Painting Materials
PE/SMP/PVC/PVDF

Standard:

 
PPGI
 
GB/T12754-06
JIS G 3312
EN 10169
CQ
TDC51D+Z
CGCC
DX51D+Z
DQ
TDC52D+Z
CGCD
DX52D+Z
 
TS250GD+Z
TS280GD+Z
TS320GD+Z
TS350GD+Z
 
S250GD+Z
S260GD+Z
S320GD+Z
S350GD+Z

Applications:
Outdoor: roof, roof structure, surface sheet of balcony, frame of window, door, garage doors, roller shutter door, booth, Persian blinds, cabana, refrigerated wagon and so on.
Indoor: door, isolators, frame of door, light steel structure of house, sliding door, folding screen, ceiling, internal decoration of toilet and elevator.

Note for Processing of Color Coated Seel Sheet:

Notes for Cutting:
a. Minimize the area of flash of cutting edge, otherwise color coated steel sheet would be scratched in stock.
b. Remove the flash and powder generated from cutting as soon as possible, or they will harm the surface of steel sheet and form the source of scratch and roasting.
c. When cutting the color coated steel sheet, plastic roller should be adopted. Adding a rubber cushion to the surface of steel sheet could be a better choice for avoiding damage to surface.

Notes for Curving:
a. Remove the remainder and roast attached to the parts in stamping processing as they may cause scratch ,dent and reduce the durability.
b. As the outer edge of curved part could be elongated after processing, slight wrinkle may be generated, but not a problem yet. Maximizing the curving rate of processing part could eliminate this defect.
c. Thickness of coating layer should be taken into account when setting the clearance between punch and die.
d. As the coating appliqué may become fragile when temperature is too low, thus wrinkle, sink and slipping may arise during the processing in low temperature. Deformation processing should be avoided when the temperature of steel sheet is lower than 21 ℃.Should temperature of environment becomes too low, warming the steel sheet could be a better choice.
e. In order to keep the formation roller and surface of steel sheet from damaging and scratch, formation roller (such as quenched steel and mold die) made of hard material should be adopted. Chrome should be galvanized to the surface of roller.
f. It is advisable to add protective appliqué onto the surface of color coated steel sheet. When the construction finished, protective appliqué could be removed.

Requirement of Transporting the Color Coated Steel Sheet
a. Keep the color coated steel sheet far from water and sunshine .It is advisable to store them indoors.
b. Should the color coated steel sheet be rained or dewing, please dry them as soon as possible so as to remove humidity.
c. Keep the inventory as the same as it shipped from factory, do not stock as piles so as to protect the coating layer.
d. It is strongly recommended to consume the steel sheet that comes into the inventory earlier. Otherwise, pollution, scratch and color aberration may arise as steel sheet produced at different date mixed together.
e. Transport the steel sheet as it shipped out of factory. Releasing the cushion and reversing the package is highly harmful.
f. When unloading the steel sheet or steel coil, rubber cushion and lift must be adopted for the sake of avoiding scratch.
g. Clean the carriage of transporting the color coated steel sheet and add rubber cushion or adopt protective instrument .
h. Vertical packaging is advised for transporting color coated steel sheet. Coil down ending machine should be used to put the coils horizontally.
i. Steel sheet and coils should be fixed well prior to transportation ,otherwise they will move and cause scratch.
j. When take out color coated steel sheets, do not pull. Otherwise, flash of cutting section and edge will cause dent and scratches.


» View all the Pre-Painted Products